Your supplier needs regular readings from your gas or electricity meter to work out your bills. If you don’t send them readings, they’ll estimate your usage. This means your bill might be too high or low.

Call your supplier to give them the readings – or check if you can submit one on their website or app.

If you have a smart meter

Smart meters are different to standard meters – they normally send readings to your supplier automatically.

You’ll normally also get a portable device called an ‘in-home display’ – this shows how much you’re spending on your energy.

Single rate digital meter

Examplehttps://images.ctfassets.net/vms0u05139aw/single_rate_digital_electricity_meter.png/b9b2eb5a637655e7a23fd4ec4f0007b3/single_rate_digital_electricity_meter.png

This meter reading is 75085. The red number should be ignored. 

A digital meter has an electronic or digital display. It will show 5 numbers in black or white, and might be followed by 1 or more red numbers.

To read the meter:

  1. Write down the first 5 numbers shown from left to right.
  2. Ignore any other numbers.

Two rate digital meter

Examplehttps://images.ctfassets.net/vms0u05139aw/two_rate_digital_electricity_meter.png/348cc88240513516445e3a67d6fea2b5/two_rate_digital_electricity_meter.png

This meter has 2 readings – 25404 and 54250. You’ll need to give both readings to your supplier.

If you get cheaper electricity at certain times, you might have a two rate (or ‘dual-rate’) meter. This means it will have 2 rows of numbers.

The top row (labelled ‘low’ or ‘night’) shows how many units of cheaper electricity you’ve used.

The bottom row (labelled ‘normal’ or ‘day’) shows how many units of standard-price electricity you’ve used.

To read the meter:

  1. Read both the top and bottom rows.
  2. Write down the numbers shown left to right.
  3. Ignore any numbers shown in red.

Two rate single display meter

Examplehttps://images.ctfassets.net/vms0u05139aw/two_rate_single_display_electricity_meter.png/2109cb7240d94a53a70e96a00c0aed10/two_rate_single_display_electricity_meter.png

This meter has 2 readings – 75085 and 46806. You’ll need to give both readings to your supplier.

Some two rate (or ‘dual rate’) meters only have 1 digital display. They will either flash up the different rate readings in a cycle or have a button that you need to press to make the display cycle through the readings for the different rates.

Most meters will have a label that tells you which rate is ‘low’ or ‘night’ and which is ‘high’ or ‘normal’. If there’s an ‘N’ on the label this will stand for ‘normal’ – it doesn’t stand for ‘night’. 

If you’re not sure which rate is which, make a note of the numbers in the morning and check again later that day. The number that’s changed must be your ‘high’ or ‘normal’ rate. 

To read the meter write down the numbers shown left to right, for each reading.

To read this meter:

  1. Write down the numbers shown left to right.
  2. Make sure you get both readings.

There might be more numbers after the high and low rates. You don’t need any of these extra numbers for your reading.

Dial meter

Examplehttps://images.ctfassets.net/vms0u05139aw/dial_meter_electric.png/d96c9368b53cf468216c069ed774bcee/dial_meter_electric.png

The dials show 1 5 6 5 9. After following the meter reading instructions, the meter reading you would give to your supplier is 1 5 6 4 9.

An electricity dial meter has 5 or more dials. They each turn to point to a number between 0 and 9.

Each dial on your meter will turn in the opposite direction to the ones next to it. Some dial meters start with a clockwise dial and some start with an anticlockwise dial – check the direction of your dials before you read them.

To read the meter:

  1. Read the first 5 dials from left to right – ignore any red dials or dials marked 1/10.
  2. If the pointer is between two numbers, write down the lower number – if it’s between 9 and 0, write down 9.
  3. If the pointer is directly over a number, write down that number and underline it.

If you’ve underlined a number, check the next dial to the right. If the pointer on that dial is between 9 and 0, reduce the number you’ve underlined by 1. For example, if you originally wrote down 5, change it to 4.